Don't over-tighten the bolts, or it can break the porcelain.
Bolt the tank to the bowl using the wrench and a screwdriver.īe careful. Place the tank onto the bowl making sure that the spud washer goes through the hole in the bowl. Turn the tank over and use the spud wrench or channel-type pliers to tighten the spud nut onto the tailpiece. Position the valve so the overflow pipe is next to the ball cock. Put the flush valve into the hole in the tank so the little tailpiece sticks out the bottom. Put the cone washer over the tailpiece so the beveled edge of the washer faces up toward the pipe. Use a spud wrench or channel-type pliers and unscrew the spud nut. Take the spud washer off the pipe that sticks out of the bottom of the tank. Lift the tank off the bowl and turn it over. It might be stuck on tightly, so grab the bolt with the wrench and use a screwdriver to unscrew the bolt. This is the tube that runs from the tank to the angle stop. Step 2: Remove Supply Tubeĭisconnect the supply tube from the tank using a wrench. Soak up any remaining water with a mop or sponge. Flush the toilet to get rid of the water in the tank. Shut off the water by turning the angle stop, the shut-off valve at the bottom of the toilet. Because the valve is made of rubber, it can decompose or warp allowing water to escape from the tank into the bowl. Replacing the Toilet Flush ValveĪ continuously running toilet can also be the result of a faulty flush valve.
Move the float cup up to raise the water level and move the cup down to lower the water. Adjust the ball cock by pinching the spring clip. Step 6: Correct Water LevelĪdjust the water so that it is 1/4" below the top of the overflow tube. Turn the water back on at the shut-off valve. If you don't have any more repairs to make, you can reattach the supply tube to the tank. Step 4: Reattach Supply TubeĪttach the coupling nut on the underside of the tank with the wrench. Bend the refill tube so the tip fits into the overflow tube on the flush valve. Adjust it so that the lid fits on the toilet. Place the new ball cock through the hole in the tank. Take off the mounting nut and remove the ball cock. The supply tube is the tube that runs from the angle stop to the tank. Using a wrench, disconnect the supply tube from the tank. Step 2: Undo Supply Tube and Remove Ball Cock Flush the toilet to empty the water in the tank. Shut off the water by turning the angle stop - the shut-off valve at the bottom of the toilet. A brass plunger-valve ball cock can warp and rust while the plastic of the float cup stays intact. The float cup variety is made of plastic, so you don't have to replace it as often. Replacing an old ball cock with a float cup will not only fix your toilet, it will make it more water efficient as well. If the chain or water level is fine but your toilet is still giving you problems, you may need to replace the ball cock. If this doesn't stop leakage, you may need to replace the wax ring. To fix this problem, sit on the toilet and twist it back into position.
#HOW DO I REMOVE TOILET TANK BOLTS THAT ARE STUCK CRACK#
Shifting can crack the wax seal and allow water to seep out from underneath. If your toilet is leaking, check to see if the toilet has shifted. This enables you to move the float cup up and down by the pull rod. If you have a float cup ball cock, you need to pinch the spring clip that is on the float cup. Bending the arm up will raise the water level, bending it down lowers it. You can repair the ball cock by bending the float arm up or down to adjust the water level for the plunger-valve ball cock. If you think you may need to replace the ball cock, go to Replace the Ball Cock. Adjust the ball cock so the water comes to1/2" below the overflow pipe.
This can be fixed by adjusting the ball cock, which is located next to the overflow pipe the open tube to the right of the handle. Improper water levels can also cause problems with your toilet. To fix it, remove links from the chain using needle-nosed pliers until it's tight.
The chain attached to the rubber flapper often becomes loose, causing incomplete flushing and/or continuous running. Jiggling the handle might work for a while, but if your toilet is always running or doesn't flush adequately, you need to perform these simple fixes that usually can tame a noisy, inefficient toilet. Best of all, you can repair them yourself. Is your toilet not functioning properly? Maybe it flushes poorly, runs continuously or leaks water? Fortunately, most problems are fixable.
0 kommentar(er)
